Pars Drain Mesh drainage sheets act as a base for shotcrete and plaster and provide efficient drainage on:
    •    Basement walls
    •    Tunnels
    •    Excavated rock surfaces

    Pars Drain Mesh is a dimpled plastic drainage sheet with an integrated plastic mesh. It is used as a base for plastering or shotcreting on walled underground structures, excavated rock surfaces and tunnels.
    The dimpled sheet also acts as a seepage layer to control dampness on basement walls. The dimples provide an air gap for reliable ventilation between the outer and inner walls.

    Pars Drain Mesh creates an effective vapour barrier and the integrated plastic mesh ensures efficient bonding of the plaster or shotcrete to the dimpled sheet. Plaster boards and timber panels may be used as alternative finishes that are fastened using proprietary Pars Drain fixing accessories.

    Dimpled drainage sheets containing an integrated mesh offer many benefits including:
    •    Wide, lightweight rolls that allow rapid and low cost installation
    •    Rolls that are easily mechanically fastened to walls or excavated rock surfaces
    •    Provision of efficient drainage, thermal insulation and vapour barriers on vertical walls and excavated surfaces
    •    Creation of a seepage layer for internal dampness control of basement walls

    Dimpled Drain Sheet + Geo textile
    Material: 100% New HDPE + PP Nonwoven
    Dimple height: 8.5 mm
    Roll Width: 255cm
    Weight of per unit area: 800-1200 gr/ m² (+/- 3%)
    Air gap volume between dimple: 5.8 L/ m²
    Temperature range: Minus 30 to 80 C
    approx. 4.6 l/s/m Drainage Capacity:
    approx. 276 l/min/m
    approx. 16500 l/h/m
    Compression strength: up to 260 KN/m2 (26 ton/ m2 ) according to customer request
    Toxicity: Non Toxic, Non Polluting
    Number of dimple: Approximately 2000 per unit
    Service life expectancy: > 25 years at (PH between 4 and 9 and temperature < 25 C).
    Biological / chemical resistance: Resistant to ground chemicals, rot, moulds, algae, bacteria and root penetration. Does not affect potable water.
    Fire resistance: B2 (DIN 4102) according to customer request
    Standards: Pars Drain is manufactured and tested according to DIN 18 195, DIN 4095, DIN 4102, DIN 53 576 and BS 8102

    1. Plaster/shortcrete
    2. Pars Drain edge profile
    3. Pars Drain Mesh
    4. Concrete slab
    5. Basement wall/rock
    6. Pars Drain
    7. Compacted gravel
    8. Sub-soil drain

    Having Integrated Management System ISO 9001:2008 certified from ICIM Italy.

    Product and Company Identification

    TRADEMARK: ParsSdra Air bubble wrap

    PRODUCT TYPE: Air bubble wrap

    MANUFACTURER: ParsSadra Co.

    No. 1625, Oghab St. Saadi Blvd, Abbas Abad Industrial Town, 35th Km Khavaran Road, Tehran 33931-77763 Iran Tel.: +98 21 36424841 Fax: +98 21 36424844

    Composition/Information on Ingredients

    High-density polyethylene

    Hazards Identification

    Under normal conditions, the product is not dangerous.

    First Aid Measures

    Skin contact: In case of burns caused by hot substance, clean the area with plenty of cold water to remove heat. Consult a physician if burning sensation persists. ALL BURNS REQUIRE MEDICAL ATTENTION.

    Fire Fighting Measures

    Appropriate extinguishing media: Dry chemical, Foam, CO2, Sand, Water spray. NEVER USE DIRECT WATER JET.

    Risks of exposure: Prolonged exposure to hot fumes causes respiratory problems.

    Firefighting equipment for fire brigade: Respiratory protection.

    Accidental Release Measures

    INDIVIDUAL PRECAUTIONS: None

    ENVIRONMENT PROTECTION: None

    CLEANING SYSTEMS: None

    Handling and Storage

    Handling: No special measures required.

    Storage: Keep away from fire. Use in places with good ventilation, preferably with fire security system. Store under cover.

    Exposure Controls and Personal Protection

    Personal protection: When manipulating hot product, wear protective clothing (helmet, gloves, boots, etc. resistant to high temperature). Avoid contact with skin. Under normal conditions it is not necessary to use breathing apparatus, it is enough with a good ventilation to minimise risk of overexposure to vapour, fumes or dust.

    Physical and Chemical Properties

    Physical state: Solid at room temperature.

    Color: White.

    Odour: None.

    Stability and Reactivity Data

    Conditions: It does not degrade with adequate use.

    Decomposition products: Thermal decomposition may produce fumes with carbon monoxide that can ignite in presence of flames or infrared panels.

    Toxicological Information

    Primary irritative effect of the skin: It does not cause irritation.

    Eye irritation: The product is not irritating.

    Additional toxicological information: According to our experience and information, the product does not cause any adverse health effect if properly handled in compliance with standard systems.

    Ecological Information

    It can be mechanically separated in a purification plant for waste water. With respect to the product´s consistency, there is no possibility of dispersion in the environment. For this reason, it does not cause any negative effect on the environment.

    Disposal Considerations

    Recycle when possible. It can also be disposed of together with household refuse or incinerated, paying attention to technical regulations and having previously consulted competent authorities.

    Transport Information

    The product is NOT considered DANGEROUS for transport (ADR, RID, UN, IATA/ICAO).

    Regulatory Information

    The product is not considered dangerous. The product does not require special labelling.

    Other Information

    This security data sheet is based on the European Community laws (91/155/CEE).